HACH LANGE ORBISPHERE 3654 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 58

HACH LANGE ORBISPHERE 3654 Скачать руководство пользователя страница 54

52

Part Lists

9.3 Analyzer spare parts

9.4 Sensor spare parts

The ORBISPHERE Recharge Kit should contain sufficient material for several years of sensor
servicing. However, it must be replenished over time.

Table 9 Analyzer spare parts

Part N°

Description

28083

Connector LEMO 6, male.

31270

TC Sensor, Substance measured: Hydrogen, Purge gas: Nitrogen, Protection cap
provided, Maximum pressure: 10 bar, External Temperature Sensor Included.

31272

TC Sensor, Substance measured: Hydrogen, Purge gas: Carbon dioxide, Protection
cap provided, Maximum pressure: 10 bar, External Temperature Sensor Included.

31570

TC Sensor, Substance measured: Nitrogen, Purge gas: Carbon dioxide, Protection
cap provided, Maximum pressure: 10 bar, External Temperature Sensor Included.

32013A

Flow chamber in PEEK, with spiral flow path for reduced flow demand for use with
TC sensors. Supplied with needle flow valve, outlet metal U-tube (6 mm outside
diameter), and 1 meter of inlet tubing.

32015.021/021

Flow chamber in PEEK with Swagelock fittings, for use with H

2

radiation resistant

applications. With spiral flow path for reduced flow demand. Supplied with EPDM
O-rings. No tubing supplied. Suitable for use up to 10 bar.

32051

Adapter for attaching 32007F flow cell inlet tubing to customer's sample tube.
Includes one 6mm (32813) and one 8mm (32814) rubber sealing gasket.

32311

Flow meter equipped with metal exit tube. Graduation from 10 to 100%

32537.03

3 meter RS232 cable for use with portable instruments. Supplied with LEMO 6
connector instrument end and 9D connector computer end.

32688

WIN3654 Windows software and communications cable.

32751

Battery recharger with pack of two rechargeable NiCd batteries (Europe only).

32824A

Fill adapter kit for purge gas cylinder.

32939

Off-mode external power supply.

Table 10 Sensor spare parts

Part N°

Description

28114

Membrane support mounting tool.

28129

PPS sensor storage and calibration cap.

28614

Membrane holding ring removal tool, for 31XXX series sensors.

29142

Protection cap with O-ring seal for TC Sensors 31270, 31470, 31478 & 31570.

29228

Stainless steel membrane holding ring with extraction groove.

2935A

Halar membranes, 25 µm, box of 25.

2952A

Tefzel membranes, (32 mm diameter), 25 µm. Box of 25.

29561A

PFA membranes, (32 mm diameter), 25 µm. Box of 25.

32746

Maintenance Kit for carbon dioxide, nitrogen, & hydrogen thermal conductivity sensors with
protection cap 29142 for use with the 3654. Includes membranes 29561A, membrane
holding ring 29228.01, O-rings 29039.0 and 28613.0, and tools for sensor maintenance.

32747

Maintenance Kit for hydrogen thermal conductivity sensors with protection cap 29142 for
use with the 3654. Includes membranes 2952A, membrane holding ring 29228.01, O-rings
29039.0 and 28613.0, and tools for sensor maintenance.

32920

Membrane mounting tool including centering guide and plunger.

«
...
52
53
54
55
56
...
»

Содержание ORBISPHERE 3654



























































Отзывы:

Нет отзывов