manualshive.com logo in svg

HACH LANGE ORBISPHERE 3654, Руководство пользователя, Страница: 11 / 58

Поделиться
Скачать
HACH LANGE ORBISPHERE 3654 Скачать руководство пользователя страница 11

9

Section 2

Specifications

Specifications are subject to change without notice.

2.1 Instrument specifications

Note: 

In accordance with the 

Pressure Equipment Directive 97/23/EC (Article 3.3)

, the components that 

make up the purge gas cylinder and pressure reducer, are not subject to the technical requirements of this 
directive.

GENERAL TECHNICAL DATA

Power Requirements

Batteries: two C-type cells, NiCad or alkaline, each 26 mm x 50 
mm, 2.4 to 3 volts total

Battery Autonomy

15 hours operational use, 3 weeks purge backup (power off, 
purge gas supplied)

Dimensions (HxWxD)

19.8 x 11.5 x 22 cm

Weight (including purge gas cylinder 
and sensor)

4.6 kg

Purge Gas

Nitrogen (H

2

 sensors)

Carbon Dioxide (N

2

 and H

2

 sensors)

Purge Gas Cylinder Pressure Limit 
(see also Note below)

200 bar maximum for N

2

 purge gas

60 bar maximum for CO

2

 purge gas

Purge Gas Autonomy

40 hours when cylinder filled to 200 bar of N

2

 

20 hours when cylinder filled to 100 bar of N

2

120 hours when cylinder filled with 75% of CO

2

 liquid

Capacity of Purge Gas Cylinder

65 ml

Digital Output (RS232C)

Baud rate: 4800
Data bits: 8
Stop Bits: 1
Start Bits: 0
Parity: None

Measurement Cycle Time

20 seconds

Temperature of Use

0 to 40°C (32 to 104°F)

Temperature of Sample

-5 to 35°C (23 to 95°F)

Sample Pressure Limit (32013A and 
32015 flow chambers)

< 10 bar, at <= 25° C

Enclosure Protection

IP 67

CE Certification

EN 61326-1:1997 /A1:1998 /A2:2001 /A3:2003
Directive 89/336/CE 

Содержание ORBISPHERE 3654



























































Отзывы:

Нет отзывов