H3C WA6638 Скачать руководство пользователя страница 4

Страница: 4 / 14

2-1

Installing the AP

Installation flowchart

Figure 2-1 Installation flowchart

Pre-installation tasks

Before installing the AP, perform the following tasks:

•

Connect the AP to a power source and the network. Examine the LEDs to verify that the AP is
operating correctly. For information about AP LEDs, see "

LEDs

•

Record the MAC address and serial number at the rear of the AP for future use.

Determining the installation position

Determine the installation position by observing the following principles:

•

Few obstacles such as wall exist between the AP and clients.

•

The AP is far away from electronic devices (such as microwave oven) that might generate
radio frequency (RF) noise.

•

The AP does not hinder people’s daily work and life.

•

The place is not water seeping, water soaking, or condensing.

Start

Complete pre-installation tasks

Determine

the mounting option

Wall mounting

Ceiling mounting

Connect the AP to the power

source

Connect the AP to the network

End

Install the AP

Содержание WA6638















Результаты поиска

Содержание WA6638

Отзывы:

Похожие инструкции для WA6638

Бренды по названию

Популярные бренды

H3C WA6638, Руководство пользователя

Результаты поиска

Содержание WA6638

Отзывы:

Похожие инструкции для WA6638

Бренды по названию

Популярные бренды