H3C WA2600 Series Скачать руководство пользователя страница 50

Страница: 50 / 131

6-1

DHCP Client Configuration Commands

The DHCP client configuration is supported only on the Layer 3 Ethernet interface (or subinterface)

and VLAN interface.

When multiple VLAN interfaces having the same MAC address use DHCP for IP address

acquisition via a relay agent, the DHCP server cannot be the Windows 2000 Server or Windows

2003 Server.

DHCP Client Configuration Commands

display dhcp client

Syntax

display dhcp client

[

verbose

] [

interface

interface-type interface-number

]

View

Any view

Default Level

1: Monitor level

Parameters

verbose

: Specifies verbose DHCP client information to be displayed.

interface

interface-type interface-number

: Specifies an interface of which to display DHCP client

information.

Description

Use the

display dhcp client

command to display DHCP client information. If no

interface

interface-type interface-number

is specified, DHCP client information of all interfaces will be displayed.

Examples

# Display DHCP client information of all interfaces.

<Sysname> display dhcp client

Vlan-interface1 DHCP client information:

Current machine state: BOUND

Allocated IP: 40.1.1.20 255.255.255.0

Allocated lease: 259200 seconds, T1: 129600 seconds, T2: 226800 seconds

DHCP server: 40.1.1.2

# Display verbose DHCP client information.

Содержание WA2600 Series




































































































































Результаты поиска

Содержание WA2600 Series

Отзывы:

Похожие инструкции для WA2600 Series

Бренды по названию

Популярные бренды

H3C WA2600 Series, Справочник по командам

Результаты поиска

Содержание WA2600 Series

Отзывы:

Похожие инструкции для WA2600 Series

Бренды по названию

Популярные бренды