H3C WA2600 Series Скачать руководство пользователя страница 28

Страница: 28 / 131

5-7

dhcp server ping packets

Syntax

dhcp server ping

packets

number

undo dhcp server ping

packets

View

System view

Default Level

2: System level

Parameters

number

: Number of ping packets, in the range of 0 to 10. 0 means no ping operation.

Description

Use the

dhcp server ping

packets

command to specify the maximum number of ping packets on the

DHCP server.

Use the

undo dhcp server ping packets

command to restore the default.

The number defaults to 1.

Examples

# Specify the maximum number of ping packets as 10.

<Sysname> system-view

[Sysname] dhcp server ping packets 10

dhcp server ping timeout

Syntax

dhcp server ping

timeout

milliseconds

undo dhcp server ping

timeout

View

System view

Default Level

2: System level

Parameters

milliseconds

: Response timeout value for ping packets in milliseconds, in the range of 0 to 10,000. 0

means no ping operation.

Description

Use the

dhcp server ping timeout

command to configure response timeout time of the ping packet on

the DHCP server.

Use the

undo dhcp server ping timeout

command to restore the default.

The time defaults to 500 ms.

Examples

# Specify the response timeout time as 1000 ms.

Содержание WA2600 Series




































































































































Результаты поиска

Содержание WA2600 Series

Отзывы:

Похожие инструкции для WA2600 Series

Бренды по названию

Популярные бренды

H3C WA2600 Series, Справочник по командам

Результаты поиска

Содержание WA2600 Series

Отзывы:

Похожие инструкции для WA2600 Series

Бренды по названию

Популярные бренды