H3C WA Series Скачать руководство пользователя страница 96

Страница: 96 / 133

<Sysname> display vlan 3

VLAN ID: 3

VLAN Type: static

Route Interface: configured

IP Address: 1.1.1.1

Subnet Mask: 255.255.255.0

Description: VLAN 0003

Name: VLAN 0003

Tagged Ports: none

Untagged Ports: none

Table 23

Command output

Field Description

VLAN Type

VLAN type, static or dynamic.

Route interface

Indicates whether the VLAN interface is configured or not.

Description

Description of the VLAN.

Name

Name configured for the VLAN.

IP Address

Primary IP address of the VLAN interface (available only when an IP address is
configured for the VLAN interface). To display secondary IP addresses, use the

display interface vlan-interface

command in any view or the

display this

command in VLAN interface view.

Subnet Mask

Subnet mask of the primary IP address (available only when an IP address is
configured for the VLAN interface).

Tagged Ports

Ports through which VLAN packets are sent tagged.

Untagged Ports

Ports through which VLAN packets are sent untagged.

interface vlan-interface

Syntax

interface vlan-interface

vlan-interface-id

undo interface vlan-interface

vlan-interface-id

View

System view

Default level

2: System level

Parameters

vlan-interface-id

: Specifies a VLAN interface number, ranging from 1 to 4094.

Description

Use

interface vlan-interface

to create a VLAN interface and enter its view or enter the view of an existing

VLAN interface.
Use

undo interface vlan-interface

to remove the specified VLAN interface.

Create the VLAN before you create the VLAN interface.

Содержание WA Series






































































































































Результаты поиска

Содержание WA Series

Отзывы:

H3C WA Series, Справочник команд второго уровня, Страница: 96 / 133

Результаты поиска

Содержание WA Series

Отзывы: