H3C WA Series Скачать руководство пользователя страница 92

Страница: 92 / 133

Field Description

Interface

The abbreviated interface name.

Link

The physical link state of the interface:

•

UP—The link is up.

•

ADM—The link has been administratively shut down. To recover its

physical state, perform the

undo shutdown

command.

Protocol

Protocol connection state of the interface, which can be UP, DOWN,
or UP(s).

Main IP

The main IP address of the interface.

Description

The description of the interface.

Cause

The cause of a DOWN physical link. If the port has been shut down
with the

shutdown

command, this field displays

Administratively

. To

restore the physical state of the interface, use the

undo shutdown

command.

display mac-vlan

Syntax

display mac-vlan

{

all

dynamic

mac-address

mac-address

[

mask

mac-mask

] |

static

vlan

vlan-id

}

[

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

all

: Displays all the MAC address-to-VLAN entries.

dynamic

: Displays dynamically configured MAC address-to-VLAN entries.

mac-address

mac-address

: Displays the MAC address-to-VLAN entry containing the specified MAC

address.

mask

mac-mask

: Displays the MAC address-to-VLAN entries with their MAC addresses in the specified

range.

static

: Displays the statically configured MAC address-to-VLAN entries.

vlan

vlan-id

: Displays the MAC address-to-VLAN entries associated with the specified VLAN.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Содержание WA Series






































































































































Результаты поиска

Содержание WA Series

Отзывы:

H3C WA Series, Справочник команд второго уровня, Страница: 92 / 133

Результаты поиска

Содержание WA Series

Отзывы: