manualshive.com logo in svg

H3C WA Series, Справочник команд второго уровня, Страница: 43 / 133

Поделиться
Скачать
H3C WA Series Скачать руководство пользователя страница 43

 

35 

mac-address (system view) 

Syntax 

mac-address 

{ 

dynamic 

| 

static 

}

 

mac

-

address 

interface 

interface

-

type interface

-

number

 

vlan

 

vlan

-

id

 

undo mac-address

 [ { 

dynamic

 | 

static 

}

 

mac

-

address 

interface

 interface

-

type interface

-

number

 

vlan

 

vlan

-

id

 ] 

undo mac-address

 

[

 dynamic

  |

 

static 

]

 mac-address 

interface

 interface

-

type interface

-

number 

vlan

 

vlan

-

id 

undo mac-address

 

[ 

dynamic 

|

 

static 

]

 

interface

 interface

-

type interface

-

number 

View 

System view 

Default level 

2: System level 

Parameters 

mac

-

address

: Specifies a MAC address in the format of H-H-H, where 0s at the beginning of each H 

(16-bit hexadecimal digit) can be omitted. For example, inputting "f-e2-1" indicates that the MAC 

address is "000f-00e2-0001". 

vlan 

vlan

-

id

: Specifies an existing VLAN to which the Ethernet interface belongs, where 

vlan-id

 is the 

specified VLAN ID, ranging from 1 to 4094. 

dynamic

: Specifies dynamic MAC address entries. These entries can age. 

static

: Specifies static MAC address entries. These entries do not age, but you can add or remove them. 

interface 

interface

-

type interface

-

number

: Specifies an outbound interface by its type and number. 

Description 

Use 

mac-address 

to add or modify a MAC address entry. 

Use 

undo mac-address 

to remove one or all MAC address entries. 

A static MAC address entry can overwrite a dynamic MAC address entry, but not vice versa. 
If you execute the 

undo mac-address

 command without specifying any parameters, this command 

deletes all unicast MAC address entries. 
You can delete all the MAC address entries of a VLAN, or you can choose to delete a specific type 

(dynamic or static) of MAC address entries only. You can single out certain ports and delete the 

corresponding unicast MAC address entries. 
The static MAC address entries configuration cannot survive a reboot unless you save it. The dynamic 

MAC address table entries, however, are lost at reboot whether or not you save the configuration. 
Related commands: 

display mac-address

. 

Examples 

# Add a static entry for MAC address 000f-e201-0101. All frames destined to this MAC address are sent 

out port GigabitEthernet 1/0/1 which belongs to VLAN 2. 

<Sysname> system-view 

[Sysname] mac-address static 000f-e201-0101 interface gigabitethernet 1/0/1 vlan 2 

Содержание WA Series






































































































































Отзывы:

Нет отзывов