manualshive.com logo in svg

H3C WA Series, Справочник команд второго уровня, Страница: 113 / 133

Поделиться
Скачать
H3C WA Series Скачать руководство пользователя страница 113

 

105 

Examples 

# Set the description for interface Dialer 1 to Dialer-interface. 

<Sysname> system-view 

[Sysname] interface Dialer 1 

[Sysname-Dialer1] description Dialer-interface 

ip address ppp-negotiate 

Syntax 

ip address ppp-negotiate 
undo ip address ppp-negotiate 

View 

Dialer interface view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

ip address ppp-negotiate 

to enable IP address negotiation on the local interface, so that the local 

interface can accept the IP address allocated by the peer end. 
Use 

undo ip address ppp-negotiate 

to disable IP address negotiation. 

By default, IP address negotiation is disabled. 
Related commands:

 remote address

 and 

ppp ipcp remote-address forced

.

 

Examples 

# Enable IP address negotiation on Dialer 1. 

<Sysname> system-view 

[Sysname] interface Dialer 1 

[Sysname-Dialer1] ip address ppp-negotiate 

link-protocol ppp 

Syntax 

link-protocol ppp 

View 

Dialer interface view 

Default level 

2: System level 

Parameters 

None 

Содержание WA Series






































































































































Отзывы:

Нет отзывов