H3C SecPath V100-E Скачать руководство пользователя страница 47

Страница: 47 / 71

7-2

Bits per second = 9600

Data bits = 8

Parity = none

Stop bits = 1

Flow control = none

Emulation = VT100

Reset them if they are not set to these values.

Troubleshooting Application Upgrading

Fault 1

1) Symptom

Boot the V100-E, upgrade Comware software using TFTP, and the system displays the following:

Net Port Download Menu:

1: Change Net Parameter

2: Download From Net

3: Exit to Main Menu

Enter your choice(1-3): 2

Starting the TFTP download...

Failed to connect the tftp server!!

Please check the network setting!!

2) Solution

The above symptom may be caused by either of the two problems:

The TFTP server program does not run.

The Ethernet is not connected properly.

Run the TFTP server program on the system, confirm that the IP address is set correctly and the
network cables are connected.

Fault 2

1) Symptom

Boot the V100-E, upgrade Comware software using TFTP, and the system displays the following:

Net Port Download Menu:

1: Change Net Parameter

2: Download From Net

3: Exit to Main Menu

Enter your choice(1-3): 2

Starting the TFTP download...

Failed to find the updated file

Please check the network setting!!

2) Solution

The above symptom is caused by either of the two problems:

Содержание SecPath V100-E








































































Результаты поиска

Содержание SecPath V100-E

Отзывы:

Бренды по названию

Популярные бренды

H3C SecPath V100-E, Руководство по установке

Результаты поиска

Содержание SecPath V100-E

Отзывы:

Бренды по названию

Популярные бренды