H3C SecPath F10 0 Series Скачать руководство пользователя страница 62

Страница: 62 / 68

Appendix B LEDs

This section uses the LEDs on the F1080 firewall as an example.

Figure 56 LEDs

(1) Hard disk status LED (HD0)

(2) System status LED (SYS)

(3) Hard disk status LED (HD1)

(4) 10/100/1000BASE-T copper port LED

(5) 1000BASE-X fiber port LED

(6) 10GBASE-R fiber port LED

(7) Power module LED (PWR1)

(8) Interface module LED (SLOT2)

(9) Interface module LED (SLOT1)

(10) Power module LED (PWR0)

Table 29 LED description

LED Status

Description

System status LED

Off

The firewall is not powered on or has failed.

Slow flashing (green)

The firewall is operating correctly.

Fast flashing (green)

The firewall is loading software.

Hard disk status LED

Fast flashing (green)

Data is being read from or written to the hard disk.

Steady green

The hard disk is present and operating correctly.

Interface module LED

Off

The interface module is not present or has failed.

Steady green

The interface module is operating correctly.

Power module LED

Off

The power module is not present or has failed.

Steady green

The power module is operating correctly.

10/100/1000BASE-T
copper port LED

Off

No link is present.

Steady green

A link is present.

Flashing green

The port is receiving and sending data.

1000BASE-X fiber port
LED

Off

No link is present.

Steady green

A 1000 Mbps link is present.

Flashing green

The port is receiving and sending data at 1000 Mbps.

10GBASE-R fiber port
LED

Off

No link is present.

Steady green

A 10 Gbps link is present.

Flashing green

The port is receiving and sending data at 10 Gbps.

Содержание SecPath F10 0 Series





































































Результаты поиска

Содержание SecPath F10 0 Series

Отзывы:

Похожие инструкции для SecPath F10 0 Series

Бренды по названию

Популярные бренды

H3C SecPath F10 0 Series, Руководство по установке

Результаты поиска

Содержание SecPath F10 0 Series

Отзывы:

Похожие инструкции для SecPath F10 0 Series

Бренды по названию

Популярные бренды