H3C SecPath F10 0 Series Скачать руководство пользователя страница 13

Страница: 13 / 68

be routed outdoors, connect a lightning arrester to the cable before you plug the cable into the
port.

Lightning protection

To protect the firewall from lightning better, follow these guidelines:

•

Make sure the grounding cable of the chassis is reliably grounded.

•

Make sure the grounding terminal of the AC power receptacle is reliably grounded.

•

Install a lightning arrester at the input end of the power module to enhance the lightning
protection capability of the power module.

Power supply

Verify that the power system at the installation site meets the requirements of the power modules,
including the input method and rated input voltage. For more information, see "

Appendix A Chassis

views and technical specifications

Installation tools

All installation tools are user supplied.

Crimping tool

Phillips screwdriver

Needle-nose pliers

Wire stripper

ESD wrist strap

Multimeter

Knife

Diagonal pliers

Accessories

Grounding cable

M6 screw
(user supplied)

Cage nut (user
supplied)

M4 screw

Mounting brackets for the
F1020/F1030/F1050/F1060/
F1070/F1080/F1090

Mounting bracket for
the F1005/F1010

Rubber feet

Power cord
retainer clip

Cable tie (user
supplied)

Содержание SecPath F10 0 Series





































































Результаты поиска

Содержание SecPath F10 0 Series

Отзывы:

Похожие инструкции для SecPath F10 0 Series

Бренды по названию

Популярные бренды

H3C SecPath F10 0 Series, Руководство по установке

Результаты поиска

Содержание SecPath F10 0 Series

Отзывы:

Похожие инструкции для SecPath F10 0 Series

Бренды по названию

Популярные бренды