manualshive.com logo in svg

H3C S9500 Series, Руководство по управлению

Поделиться
Скачать
H3C S9500 Series Скачать руководство пользователя страница 349

Command Manual – GRE 
H3C S9500 Series Routing Switches

 

Chapter 1  GRE Configuration Commands

 

1-12

 

1.1.10  source 

Syntax 

source

 { 

ip-address

 | 

ipv6-address

 | 

interface-type interface-number

 } 

undo source 

View 

Tunnel interface view 

Default Level 

2: System level 

Parameters 

ip-address

: Specifies the source IPv4 address for the tunnel interface. 

Ipv6-address

: Specifies the source IPv6 address for the tunnel interface. 

interface-type interface-num

: Type and number of an interface. 

Description 

Use the 

source

 command to specify the source address for a tunnel interface. 

Use the 

undo source

 command to remove the configuration. 

By default, no source address is configured for a tunnel interface. 

Note that: 

z

 

The source address of a tunnel interface is the address of the interface sending 

GRE packets and is usually the destination address of the peer tunnel interface. 

z

 

Two or more tunnel interfaces using the same encapsulation protocol must have 

different source addresses and destination addresses. 

Related commands:

 interface tunnel

 and 

destination

. 

Examples 

# Create interface Tunnel 5/0/0 and configure the IP address 192.100.1.1 as the source 

address of packets leaving that interface. 

<Sysname> system-view 

[Sysname] interface Tunnel 5/0/0 

[Sysname-Tunnel5/0/0] source 192.100.1.1 

1.1.11  tunnel-protocol  

Syntax 

tunnel-protocol

 

gre

  

Содержание S9500 Series































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды