manualshive.com logo in svg

H3C S5830V2 series, Справочник по командам, Страница: 50 / 301

Поделиться
Скачать
H3C S5830V2 series Скачать руководство пользователя страница 50

38 

dscp

 

dscp-value

: Specifies the DSCP value for IP to use in outgoing Telnet packets to indicate the 

packet transmission priority. The value range is 0 to 63. The default is 48. 

Usage guidelines 

This command is not supported in FIPS mode. 

To terminate the current Telnet connection, press 

Ctrl+K

 or execute the 

quit

 command. 

The source address or interface specified by this command is applied only to the current Telnet 
connection. 

Examples 

# Telnet to host 1.1.1.2, using 1.1.1.1 as the source IP address for outgoing Telnet packets. 

<Sysname> telnet 1.1.1.2 source ip 1.1.1.1 

Related commands 

telnet client source 

telnet client source 

Use 

telnet client source 

to specify a source IPv4 address or source interface for outgoing Telnet 

packets when the device acts as a Telnet client. 

Use 

undo telnet client source 

to remove the configuration. 

Syntax 

telnet client source 

{ 

interface

 

interface-type interface-number

 |

 ip

 

ip-address

 }

 

undo telnet client source 

Default 

No source IPv4 address or source interface is specified for outgoing Telnet packets. The source IPv4 
address is the primary IPv4 address of the outbound interface. 

Views 

System view 

Predefined user roles 

network-admin 

Parameters 

interface

 

interface-type interface-number

: Specifies a source interface. The primary IPv4 address of 

the interface will be used as the source IPv4 address for outgoing Telnet packets. 

ip

 

ip-address

: Specifies a source IPv4 address. 

Usage guidelines 

This command is not supported in FIPS mode. 

The source IPv4 address or source interface that is specified by this command applies to all Telnet 
connections. However, if a user specifies a source IPv4 address or source interface when executing 
the 

telnet

 command, the setting specified by the user takes effect. 

Examples 

# Set the source IPv4 address for outgoing Telnet packets to 1.1.1.1 when the device acts as a Telnet 
client. 

<Sysname> system-view 

[Sysname] telnet client source ip 1.1.1.1 

Содержание S5830V2 series














































































































































































































































































































Отзывы:

Нет отзывов