H3C s5820x series Скачать руководство пользователя страница 410

Страница: 410 / 488

11-47

By default, neither route reflector nor client is configured.

Related commands:

reflect between-clients

reflector cluster-id

Examples

# Configure the local device as a route reflector and specify the peer group

test

as a client.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test

[Sysname-bgp-af-ipv6] peer test reflect-client

peer route-limit (IPv6 address family view)

Syntax

peer

{

group-name

ipv4-address

ipv6-address

}

route-limit

prefix-number

[ {

alert-only

reconnect

reconnect-time

} |

percentage

] *

undo peer

{

group-name

ipv4-address

ipv6-address

}

route-limit

View

IPv6 address family view

Default Level

2: System level

Parameters

group-name

: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address

: IPv4 address of a peer.

ipv6-address

: IPv6 address of a peer.

prefix number

: Specifies the upper limit of prefixes that can be received from the peer or peer group.

The limit ranges from 1 to 8192. When the received prefixes from the peer/peer group reach the

specified upper limit, the router will disconnect from the peer/peer group.

alert-only

: When the received prefixes from the peer/peer group reach the specified upper limit, the

router will display alarm messages rather than disconnect from the peer/peer group.

reconnect-time

: Interval for the router to reconnect to the peer/peer group. The argument has no

default. It ranges from 1 to 65535 seconds.

percentage

: Specifies a percentage value. If the percentage of received routes to the upper limit

reaches the value, the router will generate alarm messages. The default is 75. The value is in the

range 1 to 100.

Description

Use the

peer route-limit

command to set the maximum number of prefixes that can be received from

a peer/peer group.

Use the

undo peer route-limit

command to restore the default.

By default, the router has no limit on prefixes from a peer/peer group.

The router will end the peer relation when the number of address prefixes received for the peer

exceeds the limit.

Содержание s5820x series









































































































































































































































































































































































































































































































Результаты поиска

Содержание s5820x series

Отзывы:

Похожие инструкции для s5820x series

Бренды по названию

Популярные бренды

H3C s5820x series, Справочник по командам

Результаты поиска

Содержание s5820x series

Отзывы:

Похожие инструкции для s5820x series

Бренды по названию

Популярные бренды