H3C S5500-SI Series Скачать руководство пользователя

Страница: 77 / 130

5-16

Specifying an assistant-edge node

When configuring an assistant-edge node, you must first configure the primary ring before

configuring the subrings.

Perform this configuration on a device to be configured as an assistant-edge node.

Follow these steps to specify an assistant-edge node:

To do…

Use the command…

Remarks

Enter system view

system-view

—

Enter RRPP domain view

rrpp domain

domain-id

—

Specify the current device as a

transit node of the primary ring,

and specify the primary port and

the secondary port

ring

ring-id

node-mode

transit

[

primary-port

interface-type

interface-number

]

[

secondary-port interface-type

interface-number

]

level

level-value

Required

Specify the current device as

the assistant-edge node of the

subring, and specify an edge

port

ring

ring-id

node-mode

assistant-edge

[

edge-port

interface-type

interface-number

]

Required

Activating an RRPP Domain

To activate an RRPP domain on the current device, enable the RRPP protocol and RRPP rings

for the RRPP domain on the current device.

Perform this operation on all nodes in the RRPP domain.

Follow these steps to activate an RRPP domain:

To do…

Use the command…

Remarks

Enter system view

system-view

—

Enable RRPP

rrpp enable

Required

Disabled by default

Enter RRPP domain view

rrpp domain

domain-id

—

Enable the specified RRPP ring

ring ring-id enable

Required

Disabled by default

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды