H3C S5500-SI Series Скачать руководство пользователя

Страница: 73 / 130

5-12

To do…

Use the command…

Remarks

Specify the primary control

VLAN for the RRPP domain

control-vlan vlan-id

Required

To ensure proper forwarding of RRPPDUs, do not enable QinQ or VLAN mapping on the

control VLANs.

To ensure that RRPPDUs can be sent and received correctly, do not configure the default

VLAN of a port accessing an RRPP ring as the primary control VLAN or the secondary

control VLAN.

To transparently transmit RRPPDUs on a device not configured with RRPP, you must

ensure only the two ports connecting the device to the RRPP ring permit the packets of the

control VLANs. Otherwise, the packets from other VLANs may go into the control VLANs in

transparent transmission mode and strike the RRPP ring.

Configuring Protected VLANs

Before configuring RRPP rings in an RRPP domain, configure the same protected VLANs for all

nodes in the RRPP domain first. All VLANs that the RRPP ports are assigned to should be

protected by the RRPP domains.

Perform this configuration on all nodes in the RRPP domain to be configured.

Follow these steps to configure protected VLANs:

To do…

Use the command…

Remarks

Enter system view

system-view

—

Enter RRPP domain view

rrpp domain

domain-id

—

Configure protected VLANs for

the RRPP domain

protected-vlan

reference-instance

instance-id-list

Required

By default, no protected VLAN is

configured for an RRPP domain.

When configuring load balancing, ensure that the protected VLANs configured for different

RRPP domains are different.

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды