H3C S5500-SI Series Скачать руководство пользователя

Страница: 72 / 130

5-11

Task

Remarks

Configuring RRPP Timers

Optional

Perform this task on the master node in the RRPP

domain.

Configuring an RRPP Ring Group

Optional

Perform this task on the edge node and assistant-edge

node in the RRPP domain.

RRPP does not have an auto election mechanism, so you must configure each node in the

ring network properly for RRPP to monitor and protect the ring network.

Before configuring RRPP, you need to construct a ring-shaped Ethernet topology

physically.

Creating an RRPP Domain

When creating an RRPP domain, specify a domain ID, which uniquely identifies an RRPP

domain. All devices in the same RRPP domain must be configured with the same domain ID.

Make this configuration on devices you want to configure as nodes in the RRPP domain.

Follow these steps to create an RRPP domain:

To do…

Use the command…

Remarks

Enter system view

system-view

—

Create an RRPP domain and

enter RRPP domain view

rrpp domain

domain-id

Required

Configuring Control VLANs

Before configuring RRPP rings in an RRPP domain, configure the same control VLANs for all

nodes in the RRPP domain first.

Perform this configuration on all nodes in the RRPP domain to be configured.

Follow these steps to configure control VLANs:

To do…

Use the command…

Remarks

Enter system view

system-view

—

Enter RRPP domain view

rrpp domain

domain-id

—

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды