H3C S5500-SI Series Скачать руководство пользователя

Страница: 61 / 130

4-21

[DeviceA-GigabitEthernet1/0/50]

%Jan 18 18:22:46:065 2010 DeviceA IFNET/3/LINK_UPDOWN: GigabitEthernet1/0/50 link status

is UP.

The output above indicates that the link status of both GigabitEthernet 1/0/50 and GigabitEthernet

1/0/51 is now up.

Troubleshooting DLDP

Symptom

Two DLDP-enabled devices, Device A and Device B, are connected through two fiber pairs, in which

two fibers are cross-connected. The unidirectional links cannot be detected; all the four ports involved

are in Advertisement state.

Analysis

The problem can be caused by the following.

The intervals to send Advertisement packets on Device A and Device B are not the same.

DLDP authentication modes/passwords on Device A and Device B are not the same.

Solution

Make sure the interval to send Advertisement packets, the authentication mode, and the password

configured on Device A and Device B are the same.

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды