H3C S5500-SI Series Скачать руководство пользователя

Страница: 24 / 130

2-11

Ethernet OAM Configuration Example

Network requirements

Enable Ethernet OAM on Device A and Device B to auto-detect link errors between the two

devices.

Monitor the performance of the link between Device A and Device B by collecting statistics about

the error frames received by Device A.

Figure 2-2

Network diagram for Ethernet OAM configuration

Configuration procedure

1) Configure

Device

# Configure GigabitEthernet 1/0/1 to operate in passive Ethernet OAM mode and enable Ethernet

OAM for it.

<DeviceA> system-view

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] oam mode passivez

[DeviceA-GigabitEthernet1/0/1] oam enable

[DeviceA-GigabitEthernet1/0/1] quit

# Set the errored frame detection interval to 20 seconds and set the errored frame event triggering

threshold to 10.

[DeviceA] oam errored-frame period 20

[DeviceA] oam errored-frame threshold 10

2) Configure

Device

# Configure GigabitEthernet 1/0/1 to operate in active Ethernet OAM mode (the default) and enable

Ethernet OAM for it.

<DeviceB> system-view

[DeviceB] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] oam mode active

[DeviceB-GigabitEthernet1/0/1] oam enable

[DeviceB-GigabitEthernet1/0/1] quit

3) Verify the configuration

Use the

display oam configuration

command to display the Ethernet OAM configuration. For

example:

# Display the Ethernet OAM configuration on Device A.

[DeviceA] display oam configuration

Configuration of the link event window/threshold :

--------------------------------------------------------------------------

Errored-symbol Event period(in seconds) : 1

Errored-symbol Event threshold : 1

Errored-frame Event period(in seconds) : 20

Errored-frame Event threshold : 10

Errored-frame-period Event period(in ms) : 1000

Errored-frame-period Event threshold : 1

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды