H3C S5500-SI Series Скачать руководство пользователя

Страница: 20 / 130

2-7

Configuring Basic Ethernet OAM Functions

As for Ethernet OAM connection establishment, a device can operate in active mode or passive mode.

After Ethernet OAM is enabled on an Ethernet port, according to its Ethernet OAM mode, the Ethernet

port establishes an Ethernet OAM connection with its peer port.

Follow these steps to configure basic Ethernet OAM functions:

To do…

Use the command…

Remarks

Enter system view

System-view

—

Enter Ethernet port view

interface

interface-type

interface-number

—

Set Ethernet OAM operating mode

oam mode

{

active

passive

}

Optional

The default is active Ethernet OAM

mode.

Enable Ethernet OAM on the

current port

oam enable

Required

Ethernet OAM is disabled by

default.

To change the Ethernet OAM operating mode on an Ethernet OAM-enabled port, you need to first

disable Ethernet OAM on the port.

Configuring Link Monitoring

After Ethernet OAM connections are established, the link monitoring periods and thresholds

configured in this section take effect on all Ethernet ports automatically.

Configuring Errored Symbol Event Detection

An errored symbol event occurs when the number of detected symbol errors over a specific detection

interval exceeds the predefined threshold.

Follow these steps to configure errored symbol event detection:

To do…

Use the command…

Remarks

Enter system view

system-view

—

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды