H3C S5150-EI Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 59

background image

12

Figure 9 ND MAD scenario

Hardware compatibility

An S5150-EI switch can form an IRF fabric only with devices in the same series.

General restrictions and configuration guidelines

For a successful IRF setup, follow the restrictions and guidelines in this section and the setup
procedure in "

Setup and configuration task list

Software requirements

All IRF member devices must run the same software image version. Make sure the software
auto-update feature is enabled on all member devices.

IRF physical interface requirements

Candidate IRF physical interfaces

Use the 10GBase-T Ethernet ports or SFP+ ports on the front panel of the S5150-EI switch for IRF
links.

Selecting transceiver modules and cables

When you select transceiver modules and cables, follow these restrictions and guidelines:

Device

Master

Subordinate

IRF

fabric

Internet

Customer

premise
network

IRF link

Common traffic path

Extended ND traffic path

STP domain (all devices

must run the spanning

tree feature)

«
...
16
17
18
19
20
...
»

Содержание S5150-EI Series




























































Отзывы:

Нет отзывов

Похожие инструкции для S5150-EI Series

Бренд: Ubiquiti Страницы: 24

S5500-HI Switch Series

Бренд: H3C Страницы: 180

Бренд: H3C Страницы: 84

Бренд: H3C Страницы: 281

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 102

S12500CR Series

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 15

H3C S7500E Series

Бренд: H3C Страницы: 1565

Бренд: H3C Страницы: 4

Бренд: JCG Страницы: 3

Бренд: Quick Eagle Networks Страницы: 4

Бренд: Patton electronics Страницы: 2

ipRocketLink 3086FR

Бренд: Patton electronics Страницы: 6

Бренд: Patton electronics Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды