H3C S5120-EI Series Скачать руководство пользователя страница 4

Страница: 4 / 242

Command reference

Added and modified commands

Loopback and null interface
configuration commands

Added commands: reset counters interface null
Modified commands: reset counters interface is changed into
reset counters interface loopback

MAC address table
configuration commands

None

MAC Information
configuration commands

None

Ethernet link aggregation
configuration commands

Added commands:

•

display interface bridge-aggregation

•

lacp period short

•

link-aggregation lacp traffic-redirect-notification enable

•

link-aggregation load-sharing mode local-first

Port isolation configuration
commands

None

MSTP configuration
commands

Added commands: display stp bpdu-statistics

BPDU tunneling configuration
commands

•

None

VLAN configuration
commands

Added commands:

•

mac-vlan trigger enable

•

port pvid disable

Isolate-user-VLAN
configuration commands

Added commands:

•

isolated-vlan enable

•

port isolate-user-vlan

Voice VLAN configuration
commands

Added commands:

•

voice vlan qos

•

voice vlan qos trust

GVRP configuration
commands

None

QinQ configuration
commands

Added commands: qinq transparent-vlan

LLDP configuration
commands

None

Conventions

This section describes the conventions used in this documentation set.

Command conventions

Convention Description

Boldface

Bold text represents commands and keywords that you enter literally as shown.

Italic

Italic text represents arguments that you replace with actual values.

[ ]

Square brackets enclose syntax choices (keywords or arguments) that are
optional.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды