H3C S5120-EI Series Скачать руководство пользователя страница 166

Страница: 166 / 242

154

After configuring the default VLAN for a trunk port, you must use the

port trunk permit vlan

command to

configure the trunk port to allow packets from the default VLAN to pass through, so that the port can

forward packets from the default VLAN.
Related commands:

port link-type

and

port trunk permit vlan

Examples

# Configure VLAN 100 as the default VLAN of the trunk port GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type trunk

[Sysname-GigabitEthernet1/0/1] port trunk pvid vlan 100

# Configure VLAN 100 as the default VLAN of the trunk Layer 2 aggregate interface

Bridge-aggregation

, assuming Bridge-aggregation 1 does not have member ports.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port trunk pvid vlan 100

# Configure VLAN 100 as the default VLAN of the trunk Layer 2 aggregate interface

Bridge-aggregation

. Among the member ports of the aggregation group corresponding to

Bridge-aggregation 1

GigabitEthernet 1/0/2 is an access port and GigabitEthernet 1/0/3 is a trunk port.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port trunk pvid vlan 100

Error: Failed to configure on interface GigabitEthernet1/0/2! This port is not a Trunk

port!

The output shows that the configuration on Bridge-aggregation 1 and the member port GigabitEthernet
1/0/3 succeeded; the configuration on GigabitEthernet 1/0/2 failed because GigabitEthernet 1/0/2

was not a trunk port.

MAC address-based VLAN configuration

commands

display mac-vlan

Syntax

display mac-vlan

{

all

dynamic

mac-address

mac-address

[

mask

mac-mask

] |

static

vlan

vlan-id

}

[

{

begin

exclude

include

}

regular-expression

]

View

Any view

Default level

1: Monitor level

Parameters

all

: Displays all the MAC address-to-VLAN entries.

dynamic

: Displays dynamically configured MAC address-to-VLAN entries.

Содержание S5120-EI Series



















































































































































































































































Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды

H3C S5120-EI Series, Справочник по командам

Результаты поиска

Содержание S5120-EI Series

Отзывы:

Бренды по названию

Популярные бренды