manualshive.com logo in svg

H3C S5120-EI Series, Справочник по командам

Поделиться
Скачать
H3C S5120-EI Series Скачать руководство пользователя страница 146

 

134 

Settings made in Ethernet interface view or Layer 2 aggregate interface view take effect only on the 

current port; settings made in port group view take effect on all ports in the port group. 
Before enabling BPDU tunneling for DLDP, EOAM, GVRP, HGMP, LLDP, or STP on a port, disable the 
protocol on the port.  
To enable BPDU tunneling for PVST (which is an spanning tree protocol) on a port, disable STP first and 

then enable BPDU tunneling for STP on the port. 
Before enabling BPDU tunneling for LACP on a member port of a link aggregation group, remove the 

port from the link aggregation group. 

Examples 

# Disable STP on GigabitEthernet 1/0/1, and then enable BPDU tunneling for STP on the port.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] undo stp enable 

[Sysname-GigabitEthernet1/0/1] bpdu-tunnel dot1q stp 

# Disable STP for port group 1, and then enable BPDU tunneling for STP in the port group.  

<Sysname> system-view 

[Sysname] port-group manual 1 

[Sysname-port-group-manual-1] group-member gigabitethernet 1/0/1 to gigabitethernet 

1/0/6 

[Sysname-port-group-manual-1] undo stp enable 

[Sysname-port-group-manual-1] bpdu-tunnel dot1q stp 

# Disable STP on Layer 2 aggregate interface 1, and then enable BPDU tunneling for STP on the port.  

<Sysname> system-view 

[Sysname] interface bridge-aggregation 1 

[Sysname-Bridge-Aggregation1] undo stp enable 

[Sysname-Bridge-Aggregation1] bpdu-tunnel dot1q stp 

bpdu-tunnel tunnel-dmac 

Syntax 

bpdu-tunnel tunnel-dmac

 

mac

-

address

 

undo bpdu-tunnel tunnel-dmac 

View 

System view 

Default level 

2: System level 

Parameters 

mac

-

address

: Destination multicast MAC address for BPDUs, in the format of H-H-H. The allowed values 

are 0x0100-0CCD-CDD0, 0x0100-0CCD-CDD1, 0x0100-0CCD-CDD2, and 0x010F-E200-0003. 

Description 

Use the 

bpdu-tunnel tunnel-dmac

 command to configure the destination multicast MAC address for 

BPDUs. 
Use the 

undo bpdu-tunnel tunnel-dmac

 command to restore the default value. 

Содержание S5120-EI Series



















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды