H3C S12500-X Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 168

background image

8

Installing the switch

IMPORTANT:

Keep the packages of the switch and the components for future use.

Confirming installation preparations

Before you install an S12500-X switch, verify that:

•

You have read "

Preparing for installation

" carefully and the installation site meets all the

requirements.

•

A 19-inch rack is ready for use and the rack has enough space to accommodate the switch . For
information about how to install a rack, see the rack installation guide.

•

The rack is sturdy and securely grounded.

•

No debris exists inside or around the rack.

•

The heaviest device is placed at the bottom of the rack.

•

The rack power supplying capabilities meet the device requirements. For information about the
system and module power consumptions, see "

Appendix A Chassis views and technical

." For power module specifications, see "

Appendix B FRUs and compatibility

•

The total height of the switches to be installed is no higher than the available installation height of
the rack and enough clearance is reserved for cable routing.

•

The switch is ready for installation and has been carried to a place near the rack and convenient for
moving.

Installing accessory kits

Accessory kits

Table 6

Accessory kits for the S12500-X Switch Series

Accessory kit

Description

Mounting bracket

•

Used to secure the chassis to a rack.

•

Mounted to the chassis before shipment.

•

Located at the two sides of the chassis.

•

Appearance varies by switch models.

{

S12510-X AC and S12510-X DC

—

Independent mounting brackets.

(See callout 1 in

.)

{

S12516-X AC and S12516-X DC

—

Mounting brackets are attached with

a cable management bracket.

«
...
15
16
17
18
19
...
»

Содержание S12500-X









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S12500-X

Бренд: D-Link Страницы: 36

COOPER POWER SERIES

Бренд: Eaton Страницы: 32

Бренд: Keithley Страницы: 452

Бренд: Handic Страницы: 2

Бренд: Extron electronics Страницы: 3

Бренд: Omron Страницы: 4

Бренд: ATEN Страницы: 261

Бренд: IPGARD Страницы: 2

SRW224 - 10/100 - Gigabit Switch

Бренд: Linksys Страницы: 2

Бренд: JUKI Страницы: 2

Бренд: AVLinx Страницы: 10

XTCE095F F47 Series

Бренд: Eaton Страницы: 2

Бренд: Rose electronics Страницы: 2

Бренд: Omron Страницы: 13

Бренд: ProxiMity Страницы: 4

Бренд: Larson Electronics Страницы: 2

WVCU550B - SYSTEM CONTROLLER

Бренд: Panasonic Страницы: 11

WJSX650 - SWITCHER

Бренд: Panasonic Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды