manualshive.com logo in svg

H3C S12500-X, Руководство по установке

Поделиться
Скачать
H3C S12500-X Скачать руководство пользователя страница 126

 

117 

RJ-45 port LEDs 

The LPUs provide RJ-45 port LEDs to indicate the link status and data receiving/transmitting status of the 

RJ-45 ports. 

Table 58

 

RJ-45 port LED description 

LED status 

Description

Flashing 

The RJ-45 port is receiving or transmitting data.  

Green 

A link is present. 

•

 

Gigabit RJ-45 port

—Operating at 1000 Mbps. 

•

 

10-Gigabit RJ-45 port

—Operating at 10 Gbps. 

Yellow 

A link is present. 

•

 

Gigabit RJ-45 port

—Operating at 10/100 Mbps. 

•

 

10-Gigabit RJ-45 port

—Operating at 1 Gbps. 

Off 

No link is present.  

 

SFP port LEDs 

The LPUs provide SFP port LEDs to indicate the link status and data receiving/transmitting status of the 
SFP ports. Ports 1 to 44 on the LSX1GP48EB1 are SFP ports that support only SFP modules. Ports 45 to 

48 on the LSX1GP48EB1 are SFP ports that support SFP modules, SFP+ modules, and SFP+ copper 

cables. 

Table 59

 

SFP port LED description 

LED status 

Description

Flashing 

The SFP port is receiving or transmitting data.  

Green 

A link is present. An SFP module is connected to the SFP port and the SFP 
port is operating at 1000 Mbps. 

Amber (only for ports 45 to 48 on 
the LSX1GP48EB1) 

A link is present. An SFP+ module or cable is connected to the SFP port 
and the SFP port is operating at 10 Gbps. 

Off 

No link is present.  

 

SFP+ port LEDs 

The LPUs provide one SFP+ port LED for each SFP+ port to indicate the link status and data 

receiving/transmitting status of the SFP+ ports. 

Table 60

 

SFP+ port LED description 

LED status 

Description

Flashing 

The SFP+ port is receiving or sending data.  

Green 

A link is present. The SFP+ port is operating at 10 Gbps. 

Amber 

A link is present. The SFP+ port is operating at 1000 Mbps. 

Off 

No link is present.  

 

Содержание S12500-X









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды