H3C DSIC-9FSW Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 219

background image

24

Table 33 LED description

LED Description

B1

•

Off indicates the B1 channel is idle.

•

Flashing indicates the B1 channel is being used for data communication.

B2

•

Off indicates the B2 channel is idle.

•

Flashing indicates the B1 channel is being used for data communication.

ACT

•

Off indicates the inactive state.

•

Steady on indicates the active state.

ON

•

Off indicates interface module is powered off.

•

On indicates the interface module is powered on.

Interface cables and the connection methods

For more information about BS interface cables and the connection methods, see
"

ADSL/BS/FXS/FXO/AM/FCM interface

."

Voice interface module

•

SIC-1FXS

•

SIC-1FXO

•

SIC-2FXS

•

SIC-2FXO

•

SIC-2FXS1FXO

•

DSIC-4FXS1FXO

•

SIC-1BSV

•

SIC-2BSV

•

SIC-1VE1

•

SIC-1VT1

SIC-1FXS/SIC-1FXO/SIC-2FXS/SIC-2FXO

Introduction

The 1/2-port voice subscriber circuit interface module (SIC-1FXS/SIC-2FXS) and 1/2-port voice AT0
analog trunk interface module (SIC-1FXO/SIC-2FXO) serve to access and handle 1/2 channel(s) of
analog voice signals over data communication networks. The differences between SIC-FXS and
SIC-FXO are listed below:

•

SIC-FXS modules are analog subscriber line modules that provide ordinary analog telephone
and fax access and also can connect AT0 loop trunks of exchanges.

•

SIC-FXO modules are loop trunk modules that provide access of common subscriber lines of
exchanges.

«
...
31
32
33
34
35
...
»

Содержание DSIC-9FSW




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSIC-9FSW

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 44

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

Бренд: MaintTech Страницы: 28

Бренд: Parker Страницы: 8

Бренд: Global Fire Equipment Страницы: 23

Бренд: KSB Страницы: 16

Бренд: Cardin Elettronica Страницы: 56

Бренд: AirCycler Страницы: 2

Torque Converter Lock-Up

Бренд: TS Performance Страницы: 4

Бренд: Danfoss Страницы: 8

Бренд: Swagelok Страницы: 16

Бренд: M-system Страницы: 7

Бренд: Texecom Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды