background image

page 51 of 99

cos105000_170-190_65, rev. 1.03

© 1988 - 2019 h/p/cosmos sports & medical gmbh

11.6 Safety inspection

In order to maintain the safety of the device, h/p/cosmos prescribes performance of an annual safety inspection.
Refer to the date on the inspection sticker on your device for the next inspection date.

h/p/cosmos bases the annual safety inspection on  German laws and regulations.
It is the operator’s responsibility to comply with national laws and regulations.   

The inspection label on the device also certifies the optional equipment and the accessories.
However, inspection intervals for optional equipment and accessories may deviate.

After 12 months or 5000 km there will be a safety inspection reminder (see below).

The error message will be reset by the h/p/cosmos service personnel performing the safety inspection.

11.7 Spare parts and consumables

Spare parts must only be replaced by qualified h/p/cosmos service personnel.
Information about spare parts is available at 

[email protected]

.

A list of consumables is included in the accompanying documents.

11.5 Issues for qualified service personnel

All maintenance work that is not explained in detail, must not be performed by the operator.
Safety inspections, installation and repair work, must also not be performed by the operator.
This kind of work must be performed by h/p/cosmos service personnel according to the “h/p/cosmos service instructions”.
The “h/p/cosmos service instructions” are available at 

[email protected]

.

Содержание 170-190/65 3p Series




































































































Отзывы: