background image

SPECIFICATIONS

Wingspan:......................................1400mm 

Length:...........................................1180mm 

Electric Motor:....................................750W

Glow Engine:....................  .46 2-T / .70 4-T

Radio:....................5 Channel / 4-5 Servos

Function: Ailerons-Elevator-Rudder-Throttle

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.

Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann

hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um

professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist

durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

R/C Flugmodell             R/C Airplane Model

ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY

Anleitung / Instructions

TECHNISCHE DATEN

Spannweite ...................................1400mm

Lange ............................................1180mm

Elektroantrieb.................................... 750W

Verbrennerantrieb ...............7.45cc - 11.5cc

Fluggewicht .......................................3,5Kg

Fernsteuerung ........ 5 Kanal / 4 .. 5 Servos

RTF Weight: 3.Kg (will vary with equipment

use)

TIGER MOTH 

DH-82

VQ No: VQA139R/Y/DK

Содержание TIGER MOTH DH-82





















Отзывы: