GW Instek LCR-6000 Series Скачать руководство пользователя страница 31

Страница: 31 / 143

LCR-6000 Series User Manual

4.1.2 Impedance Range [RANGE]

Impedance range mode

To achieve the best measurement result, it is
recommended to set the impedance range mode to

“Auto range”. When using “Hold range”, errors in

measurement results may occur if the measured value

exceeds the full scale of the selected range.

Table 4-4

Impedance range mode

Mode

Function
overview

Advantage

Disadvantage

Auto

Range

LCR-6000

Series sets the
optimum

impedance

range for the

impedance of
the DUT

You don’t

need to select
range

The

measurement
time is longer

due to the

ranging time

Hold

Range

Measurement

is performed with a fixed impedance range

No ranging

time is
required

You need to

select a proper
range

depending on

the value of

the DUT.

Nominal

Range

LCR-6000

Series sets the

optimum range

depending on
the nominal

value

You don’t

need to select

range. No

ranging time is
required

Valid only in

the sorting

mode

Available impedance range

The hold range has nine impedance ranges: 10, 30, 100,

300, 1k, 3k, 10k, 30k and 100k.
The impedance range is selected according to the DUT’s

impedance even if the measurement parameter is
capacitance or inductance.

Содержание LCR-6000 Series
















































































































































Результаты поиска

Содержание LCR-6000 Series

Отзывы:

Бренды по названию

Популярные бренды

GW Instek LCR-6000 Series, Руководство пользователя

Результаты поиска

Содержание LCR-6000 Series

Отзывы:

Бренды по названию

Популярные бренды