GW Instek COM-804 Скачать руководство пользователя страница 80

Страница: 80 / 157

HANDLER/SCAN INTERFACE

Bin5

High when the binning sorting result

is within the bin5 setting range.

Binning Out

Userdefine2 High or low when the user define2

logic conditions are met.

Compare,
Binning

Out

Userdefine1 High or low when the user define1

logic conditions are met.

Compare,

Binning

Out

VEXT

External DC Voltage, acceptable

range is +5V.

Ready

High when the measurement has
finished. The instrument is ready for

the next trigger.

Ext
trigger

mode

Out

Bin6

High when the binning sorting result
is within the bin6 setting range.

Binning Out

Low

High when the compare result is
deemed LO.

Compare Out

Bin7

High when the binning sorting result

is within the bin7 setting range.

Binning Out

Bin8

High when the binning sorting result
is within the bin8 setting range.

Binning Out

Bin Out

High when the binning sorting result
is out of all the bin setting ranges.

Binning Out

For backwards compatibility with the GOM-802 handler interface, please see

page 89.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание COM-804






























































































































































Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды

GW Instek COM-804, Руководство пользователя

Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды