GW Instek COM-804 Скачать руководство пользователя страница 70

Страница: 70 / 157

MEASUREMENT

Interface

Background

The remote interface can be set to RS232, GPIB or USB.

Note

The GPIB interface is only available on the GOM-804G
and the GOM-805.

1. Select
Interface setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display

has focus.
Go to System and press Enter.
Go to Utility and press Enter.
Go to Interface and press Enter.

System

menu icon

Move

Select menu

or setting

Enter

2. Interface
setting appears

Use the arrow keys to choose an interface and to set the

baud rate (RS232) or primary address (GPIB). Press
Enter to confirm the setting.

Interface

GPIB, Primary Address (1 ~ 30)

RS232, Baud Rate (1200, 2400, 4800,
9600, 19200, 38400, 57600, 115200)

USB

Note

Pressing ESC before pressing ENTER will exit from the
Interface settings.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание COM-804






























































































































































Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды

GW Instek COM-804, Руководство пользователя

Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды