GW Instek COM-804 Скачать руководство пользователя страница 15

Страница: 15 / 157

GOM-804 & GOM-805 User Manual

GND Terminal

GND

Connect the GND (ground) terminal to

the earth ground.

GUARD Terminal

GUARD

The GUARD terminal has the same

potential as earth, but cannot be
substituted for it. Connect the GUARD

terminal to the cable shield layer of the
test leads to help reduce noise.

Function Keys

Ohm

The Ohm key activates the resistance

measurement function.

Compare

The Compare key activates the
comparator function.

Binning

The Binning key activates the binning

function to grade the DUTs into eight
bins according to the tolerance settings.
GOM-805 only.

The TC key activates the TC
(temperature compensation) function

which calculates the resistance of a
DUT at a specified temperature given

the resistance of the DUT at the
ambient temperature and the

temperature coefficient of the DUT is
known.

TCONV

The TCONV (Temperature

Conversion) function calculates the
temperature of a DUT given an initial

temperature, initial resistance, measured
resistance and a constant (inferred zero

resistance temperature) for the DUT.

TEMP

The TEMP key activates the
temperature measurement function.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание COM-804






























































































































































Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды

GW Instek COM-804, Руководство пользователя

Результаты поиска

Содержание COM-804

Отзывы:

Похожие инструкции для COM-804

Бренды по названию

Популярные бренды