GUDEL NGHP Series Скачать руководство пользователя страница 121

Страница: 121 / 146

10.3

Waste management compliant assemblies

10.3.1

Disassembly

WARNING

Suspended loads

Improper handling of suspended loads can lead to severe injuries or death!

• Use appropriate lifting units

• Wear appropriate protective clothing

• Always keep sufficient distance from suspended loads

• Never enter the area below a suspended load

WARNING

Ripping of lifting belts

The sharp edges cut the lifting belts. This can lead to severe or fatal injuries!

• Always protect the lifting belts with an edge guard

CAUTION

Oil, greases

Oils and greases are harmful to the environment!

• The oils and greases must not get into the drinking water supply. Take ap-

propriate measures

• Observe the country-specific safety data sheets

• Oils and greases must be disposed of as hazardous waste, even if the total

quantity is small

Disassemble the gearbox as follows:

Remove the connecting elements (cables / energy chains)

Disassemble the gearbox and drain the oil

Disassemble the assemblies and separate the different materials

The gearbox has been disassembled.

Disposal

SERVICE MANUAL Planetary gear Güdel NRH, NRHP,
NGHP

18014399245011339_v2.0_

EN-US

121

Содержание NGHP Series



















































































































































Результаты поиска

Содержание NGHP Series

Отзывы:

Похожие инструкции для NGHP Series

Бренды по названию

Популярные бренды

GUDEL NGHP Series, Руководство по обслуживанию

Результаты поиска

Содержание NGHP Series

Отзывы:

Похожие инструкции для NGHP Series

Бренды по названию

Популярные бренды