Gude GRK 210/300 Скачать руководство пользователя страница 7

 

 

A vacuum cleaner with a common hose connection may also 
be fitted on the exhaust neck instead of the dust bag. 

(15)

 

 

Safety instructions for the operator 

 
The saw must not be used for other materials than those 
described in the Operating Instructions.  
 

 

Use the appliance only after you have thoroughly 
read the Operating Instructions. 

 

Follow all safety instructions specified in this 
manual. 

 

Behave responsibly to other persons. 

 

Procedure 

 
Switch on the trimming saw using the switch on the handgrip 
inner side. 
Before cutting, the saw disc should be turning at a maximum 
speed. Hold the handgrip of the work head and put it on 
slowly. Take care to have switching even without any jerky 
movements. Exert pressure adequate to the character and 
dimension of the material to be cut in the direction of the saw 
disc travel. The piece to be cut should be firmly pushed 
against the clamping plate. Additional supports should be 
used to enable safe cutting of long pieces.  
Upon the cut being completed, steer the head back to the 
initial position and check the saw disc cover for correct 
position. Sharpen the saw discs regularly and replace then 
when necessary. 
 

NOTICE: Never use saw discs if damaged.

 

 

Handling (Pic. 1, 3) 

 

 Never perform adjustment work when the appliance 

is running. The appliance must always be unplugged 
before adjusting! Risk of serious injury. 
 
Skew cut 

For skew cuts up to 45°, the lock lever on the rear side of the 
machine 

(13)

 should be released. 

Skew the head of the machine from the left to the required 
angle or to the end stop (45°) and then lock it with the lever 

(13).

 

 

Scarf cut 

The machine head at 45° may be turned to the right and the 
left. Smaller angles may be set easily by deducting the 
required value on the scale on the table.  Release the lock 
screw 

(14),

 turn the machine head  (grid table)  to the 

required position and fix it in required position  using the lock 
screw 

(14).

 

 

Combination Cut (horizontal and vertical up to 45°) 

 

Saw cuts combinations: 
 
 
 
 
 

 
 
 

Saw Disc Replacement (Fig. 2, 3, 4) 

 

 

CAUTION: Get down to the replacement only with the 

saw unplugged and the saw disc at standstill! 

 

Unscrew  (H), release (G) and remove the handgrip with the 
movable saw disc cover 
 
Lock the saw disc using lock knob j(l). 

 

Release the saw disc screw (J) in clockwise direction 
using a socket spanner  (left-hand thread). Remove the 
saw disc and replace with a new one, the teeth 
inclination should coincide with the direction of the arrow 
on casing.  
Before fitting in the saw disc, carefully clean the saw disc 
flange. Slip the saw disc external flange on the shaft, 
screw the lock screw on  (left-hand thread)  and fasten in 
place.  The re-fit the saw disc cover. Prior to connecting 
to the mains, test the idle run by lifting and dropping the 
work head. 

 

Step by step instructions 

 

 

Draw the guiding direction on the cut piece. 

 

Put the cut piece on the work-table and adjust the 
circular saw blade according to the mark when the 
appliance is still.  

 

Now secure the cut piece using a clamp. 

 

Check again the circular saw blade position if matching 
the mark. 

 

Switch the appliance on and perform the cut. 

 

Switch the appliance off and wait until the circular saw 
blade completely stops. 

 

Remove the sawdust and take the cut piece away.  

 

If the saw has not been used for a long time, it must 
necessarily be unplugged. 

 

Failures  -  causes  -  removal 

 

Failure Cause 

Removal 

Cut angle 
not matching

Saw head 
position not OK 

To be adjusted based on 
instructions in the “Assembly 
and first start-up“ chapter 

Engine not 
working 

Worn carbons, 
faulty switch 

Carbons to be replaced 
Repair by an expert 

 

Inspections and maintenance 

 
1. 

Have the repairs done by a skilled servicing technician 
only. Only genuine spare parts should be used.   

2. 

Protect the saw against wet and moisture conditions, 
use it in dry areas only. 

 

Maintenance (brushes and collector) 

It is recommended that you turn to a specialised servicing 
place for the brushes replacement and have the collector 
maintained on the occasion to provide for a perfect function of 
the motor. 
 

Lubrication 

All the motor bearings are lubricated sufficiently for the entire 
service life of the saw subject to normal conditions of 
operation. Maintenance is not required. 
 

Lubrication in Case of Necessity: 
1. 

Rotation axle lubrication if the run gets tight  

1.1  Loosen the set nut a put a few drops of the lubricant oil 

on the washer and the contact area.  

1.2  Remove it and lubricate the rotating axle and contact 

areas. 

NOTICE:

 Before removing the axle, the saw disc 

top cover and the end stop upper part have to be 
removed first.  The job should be accomplished by a 
skilled servicing technician. Mind the position of both the 
spring’s ends in the case. Mark it with a piece of chalk to 
facilitate re-installation.  

2. 

To provide silent and easy run of the swinging 
protective cover control lever

, all the metal and plastic 

contact areas  should be slightly lubricated with sewing 
machines oil now and then.  Take care not too use 
excessive amount of the oil.  Sawdust tends to deposit in 
the excessive oil and form hard spots. 
 

 

NOTICE

: „Unplug the machine prior to any adjustment or 

maintenance. “ 

 

Содержание GRK 210/300









Отзывы: