Gude Expert Power Control 8042 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 96

Gude Expert Power Control 8042 Series Скачать руководство пользователя страница 16

16

Expert Power Control 8042

© 2020 GUDE Systems GmbH

Operating

2

Operating

2.1

Operating the device directly

Port Switching

The current status of the output is indicated by the color of the LED. Red indicates that
the output is off, green shows that the output is on. On the device are the buttons "se-
lect" and "ok". If you press "select", the LED will blink for the first output, ie the output is
selected. Press "

select

" again to select the next output. Hold down the button "ok" for

two seconds, then the status of the selected output is toggled.

Display Information

If no port is selected manually, repeatedly pressing the "ok" button will show the IP-ad-
dress and the values of the external sensors on the display.

Status-LED

The Status LED shows the different states of the device:

·

red: The device is not connected to the Ethernet.

·

orange: The device is connected to the Ethernet and waits for data from the DHCP
server.

·

green: The device is connected to the Ethernet and the TCP/IP settings are alloc-
ated.

·

periodic blinking: The device is in Bootloader mode.

2.2

Control Panel

Access the web interface: http://"IP-address" and log-in.

«
...
14
15
16
17
18
...
»

Содержание Expert Power Control 8042 Series

































































































Отзывы:

Нет отзывов