Gude Expert Net Control 2304 Скачать руководство пользователя страница 9

Страница: 9 / 87

Expert Net Control 2304

Device Description

As an alternative to connecting "In 1-8" and "GND", voltages can also be fed in

between "In 1-8" and GND. The maximum input voltage is 24V, voltages below 3V are
detected as LOW state, and voltages above 8V are detected as HI.

1.5

Technical Specifications

Connections

1 x Ethernet connection (RJ45)
1 x RJ45 for external sensor
1 x mains connection AC (picoMAX 7.5)
1 x low voltage (screw terminal)
16 x screw terminal with 8 x input and 8 x GND

8 x relay switching contacts NO (

picoMAX 5.0)

Network connection

10/100 MBit/s 10baseT Ethernet

Relay output

max. 240V AC 16A, 50/60Hz
24V DC 10A

Power supply

internal power supply (100V to 240V AC, 50/60Hz)
Low voltage 12V to 24V AC (50/60Hz), 12V to 30V DC

Environment

Operating temperature

Storage temperature

Humidity

0°C to 50°C
-20°C - 70°C
0% - 95% (non-condensing)

Housing

White plastic

Dimensions

143mm x 65mm x 90mm (L x H x D)

Weight

approx. 400g

picoMAX® eCOM 5.0 and 7.5

Connection technology

Push-in CAGE CLAMP®

Actuation type

Push-button

Solid conductor

0.2 ... 2.5 mm² / 24 ... 12 AWG

Fine-stranded conductor

0.2 ... 2.5 mm² / 24 ... 12 AWG

Fine stranded conductor; with insulated
ferrule

0.25 ... 1.5 mm²

1.6

Sensor

One external sensor can be connected to the

Expert Net Control 2304

. The following

sensors are currently available

Содержание Expert Net Control 2304
























































































Результаты поиска

Содержание Expert Net Control 2304

Отзывы:

Gude Expert Net Control 2304, Руководство пользователя, Страница: 9 / 87

Результаты поиска

Содержание Expert Net Control 2304

Отзывы: