manualshive.com logo in svg

Gude Expert Net Control 2304, Руководство пользователя, Страница: 49 / 87

Поделиться
Скачать
Gude Expert Net Control 2304 Скачать руководство пользователя страница 49

49

Expert Net Control 2304 

 

                                                                                                                                                                                          © 2021 GUDE Systems GmbH

Configuration

Recipient address: The E-Mail address of the recipient. Additional E-Mail addresses,
separated by comma, can be specified. The input limit is 100 characters.

SMTP Server: The SMTP IP-address of the E-Mail server. Either as FQDN, e.g:
"mail.gmx.net", or as IP-address, e.g:  "213.165.64.20". If required, attach a designated
port, e.g: "mail.gmx.net:25". 

SMTP server port: The port address of the E-Mail server. In the normal case this
should be the same as the default, that is determined by the setting SMTP Connection
Security.

SMTP Connection Security: Transmission via SSL or no encryption.

SMTP Authentification (password): Authentication method of the E-Mail Server.

Username: User name that is registered with the SMTP E-Mail server.

Set new password: Enter the password for the login to the E-Mail server.

Repeat password: Enter the password again to confirm it.

  If the password mask is redisplayed, only four "bullets" are shown as a symbolic

placeholder, since for security reasons the password is never shown itself. If you want
to change a password, the complete password must always be re-entered.

E-Mail Logs: Logging of E-Mail system messages.

3.8

Front Panel

Button Lock: Disables the front buttons (activates the key lock) with the exception of
the bootloader activation.

Allow switching all ports: Allows to switch all ports on or off with the front panel buttons.

Содержание Expert Net Control 2304
























































































Отзывы:

Нет отзывов