manualshive.com logo in svg

GTT Canoga C924 Series, Руководство по установке, Страница: 11 / 81

Поделиться
Скачать
GTT Canoga C924 Series Скачать руководство пользователя страница 11

 

Canoga™ Vehicle Detectors   

Canoga™ C924X Series Installation Manual

 

 

 

Hardware Installation– 5  

 

3

 

Hardware Installation 

This section describes how to check and install card rack wiring, how to install accessory modules on 

the Canoga C924X vehicle detectors, and how to install those vehicle detectors. 

3.1

 

Pre-Installation 

Check the card rack or input file connector to be sure that it is a properly wired 44 contact card-edge 

connector. 
The connectors must be fully wired, including wired for channel synchronization and serial 

communication, to fully take advantage of the advanced features of vehicle detectors.  
In Table 3-1  C924X Vehicle Detector Card-Edge Connector Contact Assignments on page 10 indicates 

the pin assignments on the board as viewed from the front of the card rack (looking into the slot). The 

numbered contacts are on the “component side” or left side of the board, and the lettered contacts 

are on the “circuit side” or right of the board. 

Warning!  Plugging a vehicle detector into the wrong connector may cause improper operation of the 

traffic control system, which may result in personal injury.  To avoid this problem, be sure to plug 

the vehicle detector into 22/44-contact connector C924X intended for vehicle detectors.  Improper 

operation of the traffic control system may result in unsafe driver action. 

You will need card rack mounting tools, hardware as required, and connection wire that meets 

applicable electrical codes and any standards established at the installation site. 
See Section 8.2 Vehicle Detector Specifications on page 65 for power requirements. 

3.2

 

Card Rack Wiring 

1.

 

If the card rack is not pre-wired or you replaced a connector in the card rack, install the 

wiring.   
See Table 3-1  C924X Vehicle Detector Card-Edge Connector Contact Assignments on page 10  

to determine the required connections. 

2.

 

Make all connections to the pins on the rear of the card rack connector into which the vehicle 

detectors will plug.  Any of the inputs or outputs not used in your application can be left 

unconnected except in configurations where vehicle detector synchronization is used.  In this 

case, a short must be placed across the sensor inputs for unused channels. 

3.

 

If the card rack is pre-wired, verify the wiring is compatible with Table 3-1  C924X Vehicle 

Detector Card-Edge Connector Contact Assignments on page 10. 

Warning!  Improper wiring of the card rack connector may cause incorrect operation of the 

vehicle detector and affect the traffic control system, which may result in personal injury.  

To avoid this problem, verify that the card rack connectors and wiring are appropriate.  

Improper operation of the traffic control system may result in unsafe driver action. 

 

 

Содержание Canoga C924 Series


















































































Отзывы:

Нет отзывов