GST 8903, Инструкция по установке и эксплуатации

Страница: 16 / 18

HTTP://WWW.HOMBI.RU
GST8903
Intelligent Graphic Repeater Panel
Installation and Operation Manual
The Intelligent Solution
Page 14
Appendix 7 Connection of Repeater Panel
Cut the lines
between Pin 1
of mainboards
Cut the lines
between Pin 1
of mainboards
LED on the scaleboard is arranged from HL1 to HL100 viewed from Membrane
and normal direction flow; when the number of LED exceeds 100, HLQ of LED
BoardN is corresponding to N*100+Q on the scaleboard, for example HL1 on the
LED Board2 is corresponding to HL201 on the scaleboard.
- +
HLN32
HL98
+ -
LED
Board
N
HL1
HL97
+ -
HL33HL34
+ - + -
HL55HL56
+ - + -
+ - + -
HL2 XS1
HL100 HL99
+ - + -
HL63 HL62 HL61
+ - + - + - + -
HL64
HL96
+ - + - + - + -
HL95 HL94 HL93
HL32 HL31 HL30 HL29
+ - + - + - + -
HL98
+ -
LED
Board2
HL1
HL97
+ -
HL33HL34
+ - + -
HL55 HL56
+ - + -
+ - + -
HL2
XS1
HL100 HL99
+ - + -
HL63 HL62 HL61
+ - + - + - + -
HL64
HL96
+ - + - + - + -
HL95 HL94 HL93
HL32 HL31 HL30 HL29
+ - + - + - + -
Mainboard
N
Bu
zzer
XS2
XS4
XS3
Mainboard2
Buz
zer
XS2
XS4
XS3
XP
1
XS3
XS4
X03
+ - + - + - + -
HL29HL30 HL31HL32
HL93HL94 HL95
+ -
+ - + - + -
HL96
HL64
+ -
+ -
+ - + -
HL61HL62 HL63
+ - + -
HL99HL100
HL32
+ -
XS2
B
uzz
er
Buzzer
XS1 HL2
+ - + -
+ - + -
HL56 HL55
+ - + -
HL34 HL33
+ -
HL97
HL2
HL3
HL4
M ould Zone
Discharge Zone
A
V6 TCC Process Zone
F/C Performance
Test and Packing
Zone
die-casting
zone
A
HL1
HL5
+ -
HL1
N
Scaleboard
N
Mainboard1
LED
Board1
+ -
HL98
Strategic
Area
Switchboard
Name Cable No. Model and Size Length Remarks
Buzzer Cable X01
After Mainboard
soldered
Ribbon Cable X02
Flat Cable 10P
500mm
If multi-mainboards
are connected , the
lines between pin 1 of
mainboards should be
cut
Ribbon Cable X03 Flat Cable 34P 500mm
Cable 0.3 red 500mm
Connecting anodes of
indicators and anodes
on LED board
Lamp Cable XN
Cable 0.3 black 500mm
Connecting cathodes
of indicators and
cathodes on LED
board
Instruction:
1. Numbers of indicator on back box increase in sequence from left to right and from
top to bottom (HL1~HL100) viewing from membrane side.
2. Indicators on back board and on Lamp board should be soldered corresponding to
each other. Make sure the anode and cathode are correctly connected.
HTTP://GSTRU.RU E-MAIL: hombi@hombi.ru