manualshive.com logo in svg

GSi PNEG-2309, Инструкция по установке и эксплуатации

Поделиться
Скачать
GSi PNEG-2309 Скачать руководство пользователя страница 42

Chapter 4: Mixer Assembly

Installing the Bearing Guards

1. Assemble the left and right bearing guards (49 and 72) together at the top using 3/8" x 3/4" HHCS

bolts (9) and 3/8" flange nuts (21).

NOTE:

Make sure to align the access hole in the left bearing guard (49) over the grease zerk in the
bearing (50).

2. Place the assembled bearing guards (49 and 72) over the bearing (50) and fasten to the tub (27)

using 3/8" x 1" HHCS bolts (1), 3/8" flat washers (14) and 3/8" flange nuts (21) in the middle slot.

3. Install the bearing guard bottom plate (51) to the bearing guards (49 and 72) using 3/8" x 3/4" HHCS

bolts (9) and 3/8" flange nuts (21).

Figure 4-24

Installing the bearing guards

1

3/8" x 1" HHCS bolt (S-7104)

49

Left bearing guard

9

3/8" x 3/4" HHCS bolt (S-7603)

50

Bearing

14

3/8" flat washer (S-7021)

51

Bearing guard bottom plate

21

3/8" flange nut (S-8032)

72

Right bearing guard

27

Tub

42

PNEG-2309

Horizontal Fertilizer Mixer

Содержание PNEG-2309



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды