GSi PNEG-2309 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 58

background image

Chapter 4: Mixer Assembly

Installing the Sheaves and Belts

The belt guard is shipped assembled. You need to remove the front cover from the assembly before
continuing with the installation.

1. Assemble the belt guard bushing cover (42) to the belt guard cover assembly (48) using 3/8" x 3/4"

HHCS bolts (9), 3/8" flat washers (14) and 3/8" flange nuts (21).

Figure 4-17

Assembling the belt guard bushing cover with the belt guard assembly

9

3/8" x 3/4" HHCS bolt (S-7603)

42

Belt guard bushing cover

14

3/8" flat washer (S-7021)

48

Belt guard assembly

21

3/8" flange nut (S-8032)

2. Install the belt guard bushing covers (42) to the angle supports (37 and 38) using 1/2" x 1-1/2"

HHCS bolts (8), 1/2" flat washers (18) and 1/2" serrated flange nuts (23).

NOTE:

For

4-Ton mixer

: There will be one belt guard bushing cover (42) for each drive.

Figure 4-18

Installing the belt guard bushing cover to the angle supports (4-Ton mixer)

8

1/2" x 1-1/2" HHCS bolt (S-7506)

37

Left angle support

18

1/2" flat washer (S-7072)

38

Right angle support

23

1/2" serrated flange nut (S-20068)

42

Belt guard bushing cover

38

PNEG-2309

Horizontal Fertilizer Mixer

«
...
36
37
38
39
40
...
»

Содержание PNEG-2309



























































Отзывы:

Нет отзывов

Похожие инструкции для PNEG-2309

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: Jasco Страницы: 2

Бренд: Rath Страницы: 5

Бренд: Kärcher Страницы: 20

Бренд: Parker Research Corp Страницы: 3

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 114

TITAN 2967-033A

Бренд: Yetter Страницы: 20

Бренд: Sweet Sound Electronics Страницы: 6

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Бренд: Kurzweil Страницы: 91

Бренд: schmersal Страницы: 20

Бренд: GYM form Страницы: 40

COLORado Ridge IP

Бренд: Chauvet Страницы: 8

ColorSource Fresnel V

Бренд: ETC Страницы: 16

Бренд: Leister Страницы: 108

Бренд: Dale Tiffany Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды