GSI Group PNEG-1020 Скачать руководство пользователя страница 7

Страница: 7 / 48

PNEG-1020 Bin Sweep Auger

Safety

2. SAFETY

2.1 Safety Guidelines

This manual contains information that is important for you, the owner/operator, to know and

understand. This information relates to protecting

personal safety

and

preventing equipment

problems.

It is the responsibility of the owner/operator to inform anyone operating or working in

the area of this equipment of these safety guidelines. To help you recognize this information, we

use the symbols that are defined below. Please read the manual and pay attention to these

sections. Failure to read this manual and it’s safety instructions is a misuse of the equipment and

may lead to serious injury or death.

This is the safety alert symbol. It is used to alert you

to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible

injury or death.

DANGER

indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING

indicates a potentially hazardous

situation which, if not avoided, could result in death or

serious injury.

CAUTION

indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury.

CAUTION

used without the safety alert symbol indicates

a potentially hazardous situation which, if not avoided,

may result in property damage.

NOTE

indicates information about the equipment that

you should pay special attention to.

Содержание PNEG-1020

















































Результаты поиска

Содержание PNEG-1020

Отзывы:

Похожие инструкции для PNEG-1020

Бренды по названию

Популярные бренды

GSI Group PNEG-1020, Руководство по установке и эксплуатации

Результаты поиска

Содержание PNEG-1020

Отзывы:

Похожие инструкции для PNEG-1020

Бренды по названию

Популярные бренды