GSI Group PNEG-1020 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

background image

32

PNEG-1020 Bin Sweep Auger

Maintenance

9. MAINTENANCE

9.1 Maintain the Auger

ALWAYS shutdown and disconnect the power supply before adjusting, servicing or cleaning the
equipment.

1. Use caution when repairing or replacing equipment parts.

2. Make sure ALL decals are legible and tightly attached to the auger. If necessary, replace

them

FREE OF CHARGE

by contacting your dealer or the manufacturer.

3. Ensure that ALL electric motors, etc., are operating at the proper speed.

4. Maintain proper adjustments on the belt(s).

5. Mount controls for any electric motors at a safe distance from the machine and in a location

accessible in case of an emergency.

6. Make sure ALL electrical wiring is not damaged, and that it meets proper wiring codes.

7. Make sure ALL components are in good working condition before use.

8. Make sure all components are in good working condition before use.

9. Grease the bearing at least two (2) times each season.

WARNING

«
...
30
31
32
33
34
...
»

Содержание PNEG-1020

















































Отзывы:

Нет отзывов

Похожие инструкции для PNEG-1020

Бренд: Makita Страницы: 8

Бренд: VECTECH Страницы: 5

Бренд: HAMAR LASER Страницы: 49

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Precision2 HP2 Series

Бренд: B-K lighting Страницы: 6

Бренд: Zero Hand Truck Страницы: 38

Бренд: B-K lighting Страницы: 3

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды