background image

English (GB)

9

9. Hang up the end of the chain on a suitable hook 

at the top of the tank and in such a way that the 
chain cannot come into contact with the pump 
housing. 

10. Adjust the length of the motor cable by coiling it 

up on a relief fitting to ensure that the cable is not 
damaged during operation. Fasten the relief 
fitting to a suitable hook at the top of the tank. 
Make sure that the cables are not sharply bent or 
pinched.

11. Connect the motor cable and the monitoring 

cable, if any.

Hookup auto coupling

1. Fit a crossbar in the tank. 
2. Fit the stationary part of the auto coupling on top 

of the crossbar.

3. Fit the adapted piece of pipe for the movable part 

of the hookup auto coupling to the pump 
discharge port.

4. Fasten a shackle and a chain to the movable part 

of the hookup auto coupling.

5. Clean out debris from the tank before lowering 

the pump. 

6. Lower the pump into the tank by means of the 

chain secured to the lifting bracket. When the 
movable part of the auto coupling reaches the 
stationary part, the two will automatically connect 
tightly.

7. Hang up the end of the chain on a suitable hook 

at the top of the tank and in such a way that the 
chain cannot come into contact with the pump 
housing. 

8. Adjust the length of the motor cable by coiling it 

up on a relief fitting to ensure that the cable is not 
damaged during operation. Fasten the relief 
fitting to a suitable hook at the top of the tank. 
Make sure that the cables are not sharply bent or 
pinched.

9. Connect the motor cable and the monitoring 

cable, if any.

7.2 Free-standing submerged installation 

Pumps for free-standing submerged installation can 
stand freely on the bottom of the tank or the like.
The pump must be mounted on separate feet 
(accessory). 
In order to facilitate service on the pump, fit a flexible 
union or coupling to the discharge pipe for easy 
separation.
If a hose is used, make sure that the hose does not 
buckle and that the inside diameter matches that of 
the discharge port.
If a rigid pipe is used, the union or coupling, non-
return valve and isolating valve should be fitted in 
the order mentioned, when viewed from the pump.
If the pump is installed in muddy conditions or on 
uneven ground, it is recommended to support the 
pump on bricks or a similar support. 
1. Fit a 90 ° elbow to the pump discharge port and 

connect the discharge pipe/hose.

2. Lower the pump into the liquid by means of a 

chain secured to the lifting bracket of the pump. 
It is recommended to place the pump on a plane, 
solid foundation. Make sure that the pump is 
hanging from the chain and not the cable.

3. Hang up the end of the chain on a suitable hook 

at the top of the tank and in such a way that the 
chain cannot come into contact with the pump 
housing. 

4. Adjust the length of the motor cable by coiling it 

up on a relief fitting to ensure that the cable is not 
damaged during operation. Fasten the relief 
fitting to a suitable hook. Make sure that the 
cables are not sharply bent or pinched. 

5. Connect the motor cable and the monitoring 

cable, if any.

Note

Grease the gasket of the guide claw 
before lowering the pump into the tank.

When the pump has reached the base 
stand, shake the pump by means of the 
chain to make sure that it is placed in 
the correct position.

Caution

The free end of the cable must not be 
submerged as water may penetrate 
through the cable into the motor.

Caution

The free end of the cable must not be 
submerged as water may penetrate 
through the cable into the motor.

Caution

The free end of the cable must not be 
submerged as water may penetrate 
through the cable into the motor.

Содержание SEG.40.09





















Отзывы: