background image

English (GB)

11

8.3.3 Auto reset

The factory setting for this function is "on".

On

This function allows the pump to automatically check if the 
operating conditions are back to normal. If the operating 
conditions are back to normal, the alarm indication will be reset 
automatically.
The auto reset function works in the following way:

For indications, see section 

7.1.2 Indicator lights for SCALA2

.

Off

All alarms must be reset manually by means of the 

 button.

8.3.4 Anti cycling

The factory setting for this function is "off".
This function monitors the starts and stops of the pump.

Off

If the pump starts 40 times in a fixed pattern, there will be an 
alarm. The pump will remain in operation as normal.

On

If the pump starts and stops in a fixed pattern, there is a leakage 
in the system, and the pump will stop and show alarm 3.

8.3.5 Maximum continuous operating time

The factory setting for this function is "off".
This function is a timer that can turn off the pump if it runs 
continuously for 30 minutes.

Off

If the pump exceeds the running time of 30 minutes, the pump will 
run depending on the flow.

On

If the pump exceeds the running time of 30 minutes, the pump will 
stop after 30 minutes of continuous operation, and it will show 
alarm 6. This alarm will always need to be reset manually.

8.4 Resetting to factory settings

The pump can be reset to factory setting by pressing the 

 

buttons simultaneously for 5 seconds.

9. Servicing the product

9.1 Maintaining the product

9.1.1 Insect filter

The pump has an insect filter to prevent insects from nesting in 
the pump.
The filter is placed on the bottom and can easily be removed and 
cleaned with a stiff brush. See fig. 

19

.

Clean the insect filter once a year or as needed.

Fig. 19

Insect filter

9.1.2 Inlet and outlet valves

The pump is maintenance-free, but we recommend that you 
check and clean the inlet and outlet non-return valves once a 
year or as needed.

Fig. 20

SCALA2 pump

To remove the inlet non-return valve, follow the steps below:

1. Turn off the power supply and disconnect the power plug.
2. Shut off the water source.
3. Open a tap to release the pressure in the pipe system.
4. Close the isolating valves and/or drain the pipes.
5. Gradually open and remove the priming plug. See fig. 

20

 (5).

6. Remove the drain plug and drain the pump. See fig. 

20

 (8).

7. Unscrew the union nut holding the inlet connection. See fig. 

20

 (7). Depending on the installation type, it may be 

necessary to remove the pipes from both the inlet and outlet 
connections.

8. Pull out the inlet connection.
9. Pull out the inlet non-return valve.
10. Clean the non-return valve with warm water and a soft brush.
11. Assemble the components in reverse order.

Indication

Action

Water shortage

The pump will attempt eight restarts at 
five-minute intervals. If not successful, 
this cycle will be repeated after 24 hours.

Dry running (pump 
not primed)

Prime the pump and reset it manually.

All other indications

The pump will attempt three restarts 
within the first 60 seconds, then eight 
restart attempts at five-minute intervals. If 
not successful, this cycle will be repeated 
after 24 hours.

Leakage in the system.

Maximum runtime exceeded.

DANGER
Electric shock

Death or serious personal injury
- Before starting any work on the product, make 

sure that the power supply has been switched off 
and that it cannot be accidentally switched on.

TM

06

 4

537

 25

15

T

M

06

 38

18

 10

15

1

5

6

7

8

2

3

4

9

Содержание SCALA Series



















Отзывы: