background image

English (GB)

9

5.1 Contaminated products

The product will be classified as contaminated if it 
has been used for a liquid which is injurious to health 
or toxic.
If you request Grundfos to service the product, 
contact Grundfos with details about the liquid before 
returning the product for service. Otherwise, 
Grundfos can refuse to accept the product for 
service.
Any application for service must include details 
about the liquid.
Clean the product in the best possible way before 
you return it.

5.2 Maintaining the product

Pumps installed in accordance with these 
instructions require very little maintenance.

Shaft seal

The mechanical shaft seal is self-adjusting and has 
wear-resistant seal rings which are lubricated and 
cooled by the pumped liquid.

Pump bearings

The pump bearings are also lubricated by the 
pumped liquid. 

Motor bearings

The motor ball bearings are grease packed and 
sealed for life. No further lubrication is necessary. 
Pumps from 4 kW and up have angular contact 
bearings. 

5.3 Filters 

Chip trays, filters, etc. must be cleaned at regular 
intervals to ensure a correct flow of liquid. 

5.4 Periodic checks 

At regular intervals, depending on the conditions and 
time of operation, the following checks must be 
made: 

Check the quantity of liquid and operating 
pressure. 

Check that there are no leaks. 

Check that the motor is not overheating. 

Check the tripping of the motor-protective circuit 
breaker. 

Check that all controls are operating 
satisfactorily. 

If the above checks do not reveal any abnormal 
operating details, no further checks are necessary. 
Should any faults be found, check the symptoms in 
section 

6. Fault finding the product

.

Содержание MTH 10



















Отзывы: