Grundfos Hydro Multi-E Скачать руководство пользователя страница 2

Страница: 2 / 30

English (GB)

Installation and operating instructions

Original installation and operating instructions

These installation and operation instructions apply to the
Grundfos Hydro Multi-E booster systems.

CONTENTS

Page

1. Symbols used in this document

1.1 Warnings against hazards involving risk of death

or personal injury

The text accompanying the three hazard symbols DANGER,
WARNING and CAUTION is structured in the following way:

1.2 Other important notes

Symbols used in this document

1.1

Warnings against hazards involving risk of death or
personal injury

1.2

Other important notes

Scope of these instructions

System sizing

Product description

Operating conditions

7.1

Temperatures

7.2

Installation altitude

7.3

Relative humidity

7.4

Maximum operating pressure

7.5

Shaft seal run-in

7.6

Minimum inlet pressure

7.7

Maximum inlet pressure

Mechanical installation

8.3

Electrical installation

8.4

Mains supply

8.5

Additional protection

Startup

9.1

Hydro Multi-E in system with positive inlet pressure

9.2

Hydro Multi-E in system without inlet pressure

10.

Operating modes

10.1 Normal operation

10.2 Stop or Max. operation

10.3 Operating condition in case of disconnection of power

supply

10.4 Further settings

11.

User interfaces

11.1 Standard control panel

12.

Grundfos GO Remote

12.1 Communication

12.2 Menu overview for Grundfos GO Remote

13.

Multi-master function

13.1 Systems with one outlet-pressure sensor

13.2 Systems with two or more outlet-pressure sensors

14.

Protective functions

14.1 Dry-running protection

15.

Bus signal

16.

Priority of settings

Data communication

21.

Insulation resistance

23.1 Frost protection

Technical data, Hydro Multi-E with single-phase
pumps

25.1 Supply voltage

25.2 Leakage current

26.

Technical data, Hydro Multi-E with three-phase
pumps

26.1 Supply voltage

26.2 Leakage current

27.

Inputs and outputs

28.

Other technical data

29.

Sound pressure level

29.1 Hydro Multi-E with single-phase pumps

29.2 Hydro Multi-E with three-phase pumps

30.

Disposal

Prior to installation, read this document. Installation
and operation must comply with local regulations and
accepted codes of good practice.

DANGER

Indicates a hazardous situation which, if not avoided,
will result in death or serious personal injury.

WARNING

Indicates a hazardous situation which, if not avoided,
could result in death or serious personal injury.

CAUTION

Indicates a hazardous situation which, if not avoided,
could result in minor or moderate personal injury.

SIGNAL WORD
Description of hazard

Consequence of ignoring the warning.
- Action to avoid the hazard.

A blue or grey circle with a white graphical symbol
indicates that an action must be taken.

A red or grey circle with a diagonal bar, possibly with
a black graphical symbol, indicates that an action
must not be taken or must be stopped.

If these instructions are not observed, it may result in
malfunction or damage to the equipment.

Содержание Hydro Multi-E































Результаты поиска

Содержание Hydro Multi-E

Отзывы:

Похожие инструкции для Hydro Multi-E

Бренды по названию

Популярные бренды

Grundfos Hydro Multi-E, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Hydro Multi-E

Отзывы:

Похожие инструкции для Hydro Multi-E

Бренды по названию

Популярные бренды