Grundfos DMX 221 Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

background image

English (GB)

19

Fig. 22

Electrical connection of the electronics

9.2.6 Screwing the sensor into the dosing head

• Screw the sensor from the lower side into the hole of the

dosing head flange (M14 x 1.5).

– Now the diaphragm leakage sensor is ready for start-up.

9.2.7 Start-up

Functional check

• Dip the sensor into water.

– Green and red LEDs are on:

Sensor and electronics are ready for operation!

– One or more LEDs are off:

Sensor or electronics is defective!
Call Grundfos service.

• Carefully dry the sensor.

– Only the green LED is still on:

Sensor and electronics are ready for operation!

– The red LED is still on:

Sensor or electronics is defective!
Call Grundfos service.

9.2.8 Using the contacts

• Terminals 6 and 7 (potential-loaded)

– for instance for switching off the pump in case of a

diaphragm leakage.

• Terminals 8, 9 and 10 (potential-free)

– for instance for triggering an alarm device.

9.2.9 Description of the device

There are a green and a red light-emitting diode (LED) at the
electronics.
• Green LED

– shows that the system is ready for operation.
– The LED is only on when the sensor is connected to the

electronics.
If the LED is off in this case, either the sensor or the cable is
defective or wrongly connected.

• Red LED

– shows that a diaphragm leakage has been detected.
– The green LED is still on.

9.2.10 Maintenance

Sensor

Optoelectronic sensor with 3 metres cable.
• Clean the sensor in case of malfunction.
• If the sensor still does not operate correctly, replace it.

Electronics

• No maintenance is possible by the user.
• If the electronics does not operate correctly, call Grundfos

service.

TM

03

63

85

45

06

1

K1

L

1

K2

N

1

K3

PE

1

K4

PE

1

K5

N

1

K6

1

K7

K8

K9

K10

1

1

1

S1

1

1

1

S2

230 VAC /
115 VAC

Contact 1 (non floating
230 VAC / 115 VAC)

Contact 2
(floating)

Sensor

Green

Yellow

White

Caution

Carry out a functional check before start-up!

Warning
Do not open the electronics or sensor!
Repairs must only be carried out by authorised
and qualified personnel!

Warning
Do not open the electronics or sensor!
Repairs must only be carried out by authorised
and qualified personnel!

«
...
17
18
19
20
21
...
»

Содержание DMX 221 Series

































Отзывы:

Нет отзывов

Похожие инструкции для DMX 221 Series

Бренд: Waterous Страницы: 36

Бренд: Paragon Страницы: 16

Бренд: Kaisai Страницы: 40

Water Jet Lightning

Бренд: Oase Страницы: 28

AquaMax Eco Premium 4000

Бренд: Oase Страницы: 120

Бренд: Oase Страницы: 9

Бренд: WACKER Group Страницы: 60

Бренд: Liberty Pumps Страницы: 16

jumbo floodfighter

Бренд: Davey Страницы: 8

Habitat PWF105-C

Бренд: Plantronics Страницы: 33

Бренд: Binks Страницы: 22

Бренд: Xylem Страницы: 54

Бренд: Xylem Страницы: 36

Duraclad Lime Tamer

Бренд: A.O. Smith Страницы: 2

Бренд: CALPAK Страницы: 35

Бренд: Homa Страницы: 32

Бренд: Parkside Страницы: 195

Altherma 3 R MT F

Бренд: Daikin Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды